source: mainline/uspace/drv/uhci-rhd/port.c@ 7f810b3

/*
 * Copyright (c) 2011 Jan Vesely
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * - Redistributions of source code must retain the above copyright
 *   notice, this list of conditions and the following disclaimer.
 * - Redistributions in binary form must reproduce the above copyright
 *   notice, this list of conditions and the following disclaimer in the
 *   documentation and/or other materials provided with the distribution.
 * - The name of the author may not be used to endorse or promote products
 *   derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/** @addtogroup usb
 * @{
 */
/** @file
 * @brief UHCI driver
 */
#include <errno.h>
#include <str_error.h>
#include <fibril_synch.h>

#include <usb/usb.h>    /* usb_address_t */
#include <usb/usbdevice.h>
#include <usb/hub.h>
#include <usb/request.h>
#include <usb/debug.h>
#include <usb/recognise.h>

#include "port.h"

static int uhci_port_new_device(uhci_port_t *port, usb_speed_t speed);
static int uhci_port_remove_device(uhci_port_t *port);
static int uhci_port_set_enabled(uhci_port_t *port, bool enabled);
static int uhci_port_check(void *port);
static int uhci_port_reset_enable(int portno, void *arg);
/*----------------------------------------------------------------------------*/
/** Initializes UHCI root hub port instance.
 *
 * @param[in] port Memory structure to use.
 * @param[in] addr Address of I/O register.
 * @param[in] number Port number.
 * @param[in] usec Polling interval.
 * @param[in] rh Pointer to ddf instance fo the root hub driver.
 * @return Error code.
 *
 * Starts the polling fibril.
 */
int uhci_port_init(uhci_port_t *port,
    port_status_t *address, unsigned number, unsigned usec, ddf_dev_t *rh)
{
        assert(port);
        asprintf(&port->id_string, "Port (%p - %d)", port, number);
        if (port->id_string == NULL) {
                return ENOMEM;
        }

        port->address = address;
        port->number = number;
        port->wait_period_usec = usec;
        port->attached_device = 0;
        port->rh = rh;

        int rc = usb_hc_connection_initialize_from_device(
            &port->hc_connection, rh);
        if (rc != EOK) {
                usb_log_error("Failed to initialize connection to HC.");
                return rc;
        }

        port->checker = fibril_create(uhci_port_check, port);
        if (port->checker == 0) {
                usb_log_error("Port(%p - %d): failed to launch root hub fibril.",
                    port->address, port->number);
                return ENOMEM;
        }

        fibril_add_ready(port->checker);
        usb_log_debug("Port(%p - %d): Added fibril. %x\n",
            port->address, port->number, port->checker);
        return EOK;
}
/*----------------------------------------------------------------------------*/
/** Finishes UHCI root hub port instance.
 *
 * @param[in] port Memory structure to use.
 *
 * Stops the polling fibril.
 */
void uhci_port_fini(uhci_port_t *port)
{
        /* TODO: Kill fibril here */
        return;
}
/*----------------------------------------------------------------------------*/
/** Periodically checks port status and reports new devices.
 *
 * @param[in] port Memory structure to use.
 * @return Error code.
 */
int uhci_port_check(void *port)
{
        uhci_port_t *instance = port;
        assert(instance);

        while (1) {
                async_usleep(instance->wait_period_usec);

                /* read register value */
                port_status_t port_status = uhci_port_read_status(instance);

                uhci_port_print_status(instance, port_status);

                if ((port_status & STATUS_CONNECTED_CHANGED) == 0)
                        continue;

                usb_log_debug("%s: Connected change detected: %x.\n",
                    instance->id_string, port_status);

                int rc =
                    usb_hc_connection_open(&instance->hc_connection);
                if (rc != EOK) {
                        usb_log_error("%s: Failed to connect to HC.",
                            instance->id_string);
                        continue;
                }

                /* Remove any old device */
                if (instance->attached_device) {
                        usb_log_debug2("%s: Removing device.\n",
                            instance->id_string);
                        uhci_port_remove_device(instance);
                }

                if ((port_status & STATUS_CONNECTED) != 0) {
                        /* New device */
                        const usb_speed_t speed =
                            ((port_status & STATUS_LOW_SPEED) != 0) ?
                            USB_SPEED_LOW : USB_SPEED_FULL;
                        uhci_port_new_device(instance, speed);
                } else {
                        /* Write one to WC bits, to ack changes */
                        uhci_port_write_status(instance, port_status);
                        usb_log_debug("%s: status change ACK.\n",
                            instance->id_string);
                }

                rc = usb_hc_connection_close(&instance->hc_connection);
                if (rc != EOK) {
                        usb_log_error("%s: Failed to disconnect.",
                            instance->id_string);
                }
        }
        return EOK;
}
/*----------------------------------------------------------------------------*/
/** Callback for enabling port during adding a new device.
 *
 * @param portno Port number (unused).
 * @param arg Pointer to uhci_port_t of port with the new device.
 * @return Error code.
 */
int uhci_port_reset_enable(int portno, void *arg)
{
        uhci_port_t *port = (uhci_port_t *) arg;

        usb_log_debug2("%s: new_device_enable_port.\n", port->id_string);

        /*
         * The host then waits for at least 100 ms to allow completion of
         * an insertion process and for power at the device to become stable.
         */
        async_usleep(100000);

        /*
         * Resets from root ports should be nominally 50ms
         */
        {
                usb_log_debug("%s: Reset Signal start.\n", port->id_string);
                port_status_t port_status = uhci_port_read_status(port);
                port_status |= STATUS_IN_RESET;
                uhci_port_write_status(port, port_status);
                async_usleep(50000);
                port_status = uhci_port_read_status(port);
                port_status &= ~STATUS_IN_RESET;
                uhci_port_write_status(port, port_status);
                usb_log_debug("%s: Reset Signal stop.\n", port->id_string);
        }

        /* the reset recovery time 10ms */
        async_usleep(10000);

        /* Enable the port. */
        uhci_port_set_enabled(port, true);

        return EOK;
}
/*----------------------------------------------------------------------------*/
/** Initializes and reports connected device.
 *
 * @param[in] port Memory structure to use.
 * @param[in] speed Detected speed.
 * @return Error code.
 *
 * Uses libUSB function to do the actual work.
 */
int uhci_port_new_device(uhci_port_t *port, usb_speed_t speed)
{
        assert(port);
        assert(usb_hc_connection_is_opened(&port->hc_connection));

        usb_log_info("%s: Detected new device.\n", port->id_string);

        usb_address_t dev_addr;
        int rc = usb_hc_new_device_wrapper(port->rh, &port->hc_connection,
            speed, uhci_port_reset_enable, port->number, port,
            &dev_addr, &port->attached_device, NULL, NULL, NULL);

        if (rc != EOK) {
                usb_log_error("%s: Failed(%d) to add device: %s.\n",
                    port->id_string, rc, str_error(rc));
                uhci_port_set_enabled(port, false);
                return rc;
        }

        usb_log_info("%s: New device has address %d (handle %zu).\n",
            port->id_string, dev_addr, port->attached_device);

        return EOK;
}
/*----------------------------------------------------------------------------*/
/** Removes device.
 *
 * @param[in] port Memory structure to use.
 * @return Error code.
 *
 * Does not work DDF does not support device removal.
 */
int uhci_port_remove_device(uhci_port_t *port)
{
        usb_log_error("%s: Don't know how to remove device %d.\n",
            port->id_string, (unsigned int)port->attached_device);
        return EOK;
}
/*----------------------------------------------------------------------------*/
/** Enables and disables port.
 *
 * @param[in] port Memory structure to use.
 * @return Error code. (Always EOK)
 */
int uhci_port_set_enabled(uhci_port_t *port, bool enabled)
{
        assert(port);

        /* Read register value */
        port_status_t port_status = uhci_port_read_status(port);

        /* Set enabled bit */
        if (enabled) {
                port_status |= STATUS_ENABLED;
        } else {
                port_status &= ~STATUS_ENABLED;
        }

        /* Write new value. */
        uhci_port_write_status(port, port_status);

        usb_log_info("%s: %sabled port.\n",
                port->id_string, enabled ? "En" : "Dis");
        return EOK;
}
/*----------------------------------------------------------------------------*/
/**
 * @}
 */