source: mainline/uspace/drv/ehci-hcd/pci.c@ cf2ccd4

/*
 * Copyright (c) 2011 Jan Vesely
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 *
 * - Redistributions of source code must retain the above copyright
 *   notice, this list of conditions and the following disclaimer.
 * - Redistributions in binary form must reproduce the above copyright
 *   notice, this list of conditions and the following disclaimer in the
 *   documentation and/or other materials provided with the distribution.
 * - The name of the author may not be used to endorse or promote products
 *   derived from this software without specific prior written permission.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */
/**
 * @addtogroup drvusbehci
 * @{
 */
/**
 * @file
 * PCI related functions needed by the EHCI driver.
 */
#include <errno.h>
#include <assert.h>
#include <as.h>
#include <devman.h>
#include <ddi.h>
#include <libarch/ddi.h>
#include <device/hw_res.h>

#include <usb/debug.h>
#include <pci_dev_iface.h>

#include "pci.h"

#define PAGE_SIZE_MASK 0xfffff000

#define HCC_PARAMS_OFFSET 0x8
#define HCC_PARAMS_EECP_MASK 0xff
#define HCC_PARAMS_EECP_OFFSET 8

#define CMD_OFFSET 0x0
#define CONFIGFLAG_OFFSET 0x40

#define USBCMD_RUN 1

#define USBLEGSUP_OFFSET 0
#define USBLEGSUP_BIOS_CONTROL (1 << 16)
#define USBLEGSUP_OS_CONTROL (1 << 24)
#define USBLEGCTLSTS_OFFSET 4

#define DEFAULT_WAIT 10000
#define WAIT_STEP 10

/** Get address of registers and IRQ for given device.
 *
 * @param[in] dev Device asking for the addresses.
 * @param[out] mem_reg_address Base address of the memory range.
 * @param[out] mem_reg_size Size of the memory range.
 * @param[out] irq_no IRQ assigned to the device.
 * @return Error code.
 */
int pci_get_my_registers(ddf_dev_t *dev,
    uintptr_t *mem_reg_address, size_t *mem_reg_size, int *irq_no)
{
        assert(dev != NULL);

        int parent_phone = devman_parent_device_connect(dev->handle,
            IPC_FLAG_BLOCKING);
        if (parent_phone < 0) {
                return parent_phone;
        }

        int rc;

        hw_resource_list_t hw_resources;
        rc = hw_res_get_resource_list(parent_phone, &hw_resources);
        if (rc != EOK) {
                async_hangup(parent_phone);
                return rc;
        }

        uintptr_t mem_address = 0;
        size_t mem_size = 0;
        bool mem_found = false;

        int irq = 0;
        bool irq_found = false;

        size_t i;
        for (i = 0; i < hw_resources.count; i++) {
                hw_resource_t *res = &hw_resources.resources[i];
                switch (res->type)
                {
                case INTERRUPT:
                        irq = res->res.interrupt.irq;
                        irq_found = true;
                        usb_log_debug2("Found interrupt: %d.\n", irq);
                        break;

                case MEM_RANGE:
                        if (res->res.mem_range.address != 0
                            && res->res.mem_range.size != 0 ) {
                                mem_address = res->res.mem_range.address;
                                mem_size = res->res.mem_range.size;
                                usb_log_debug2("Found mem: %" PRIxn" %zu.\n",
                                    mem_address, mem_size);
                                mem_found = true;
                                }
                default:
                        break;
                }
        }

        if (mem_found && irq_found) {
                *mem_reg_address = mem_address;
                *mem_reg_size = mem_size;
                *irq_no = irq;
                rc = EOK;
        } else {
                rc = ENOENT;
        }

        async_hangup(parent_phone);
        return rc;
}
/*----------------------------------------------------------------------------*/
/** Calls the PCI driver with a request to enable interrupts
 *
 * @param[in] device Device asking for interrupts
 * @return Error code.
 */
int pci_enable_interrupts(ddf_dev_t *device)
{
        int parent_phone =
            devman_parent_device_connect(device->handle, IPC_FLAG_BLOCKING);
        if (parent_phone < 0) {
                return parent_phone;
        }
        bool enabled = hw_res_enable_interrupt(parent_phone);
        async_hangup(parent_phone);
        return enabled ? EOK : EIO;
}
/*----------------------------------------------------------------------------*/
/** Implements BIOS handoff routine as decribed in EHCI spec
 *
 * @param[in] device Device asking for interrupts
 * @return Error code.
 */
int pci_disable_legacy(ddf_dev_t *device)
{
        assert(device);
        int parent_phone = devman_parent_device_connect(device->handle,
                IPC_FLAG_BLOCKING);
        if (parent_phone < 0) {
                return parent_phone;
        }

#define CHECK_RET_HANGUP_RETURN(ret, message...) \
        if (ret != EOK) { \
                usb_log_error(message); \
                async_hangup(parent_phone); \
                return ret; \
        } else (void)0


        /* read register space BASE BAR */
        sysarg_t address = 0x10;
        sysarg_t value;

        int ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
            IPC_M_CONFIG_SPACE_READ_32, address, &value);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read PCI config space.\n",
            ret);
        usb_log_info("Register space BAR at %p:%" PRIxn ".\n", (void *) address, value);

        /* clear lower byte, it's not part of the BASE address */
        uintptr_t registers = (value & 0xffffff00);
        usb_log_info("Memory registers BASE address:%p.\n", (void *) registers);

        /* if nothing setup the hc, we don't need to turn it off */
        if (registers == 0)
                return ENOTSUP;

        /* map EHCI registers */
        void *regs = as_get_mappable_page(4096);
        ret = physmem_map((void*)(registers & PAGE_SIZE_MASK), regs, 1,
            AS_AREA_READ | AS_AREA_WRITE);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to map registers %p:%p.\n",
            ret, regs, (void *) registers);

        /* calculate value of BASE */
        registers = (registers & 0xf00) | (uintptr_t)regs;

        const uint32_t hcc_params =
            *(uint32_t*)(registers + HCC_PARAMS_OFFSET);
        usb_log_debug("Value of hcc params register: %x.\n", hcc_params);

        /* Read value of EHCI Extended Capabilities Pointer
         * (points to PCI config space) */
        uint32_t eecp =
            (hcc_params >> HCC_PARAMS_EECP_OFFSET) & HCC_PARAMS_EECP_MASK;
        usb_log_debug("Value of EECP: %x.\n", eecp);

        /* Read the second EEC. i.e. Legacy Support and Control register */
        /* TODO: Check capability type here */
        ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
            IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGCTLSTS_OFFSET, &value);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGCTLSTS.\n", ret);
        usb_log_debug("USBLEGCTLSTS: %" PRIxn ".\n", value);

        /* Read the first EEC. i.e. Legacy Support register */
        /* TODO: Check capability type here */
        ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
            IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGSUP_OFFSET, &value);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGSUP.\n", ret);
        usb_log_debug2("USBLEGSUP: %" PRIxn ".\n", value);

        /* Request control from firmware/BIOS, by writing 1 to highest byte.
         * (OS Control semaphore)*/
        ret = async_req_3_0(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
           IPC_M_CONFIG_SPACE_WRITE_8, eecp + USBLEGSUP_OFFSET + 3, 1);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to request OS EHCI control.\n",
            ret);

        size_t wait = 0;
        /* Wait for BIOS to release control. */
        while ((wait < DEFAULT_WAIT) && (value & USBLEGSUP_BIOS_CONTROL)) {
                async_usleep(WAIT_STEP);
                ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
                    IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGSUP_OFFSET, &value);
                wait += WAIT_STEP;
        }


        if ((value & USBLEGSUP_BIOS_CONTROL) == 0) {
                usb_log_info("BIOS released control after %zu usec.\n", wait);
        } else {
                /* BIOS failed to hand over control, this should not happen. */
                usb_log_warning( "BIOS failed to release control after "
                    "%zu usecs, force it.\n", wait);
                ret = async_req_3_0(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
                    IPC_M_CONFIG_SPACE_WRITE_32, eecp + USBLEGSUP_OFFSET,
                    USBLEGSUP_OS_CONTROL);
                CHECK_RET_HANGUP_RETURN(ret,
                    "Failed(%d) to force OS EHCI control.\n", ret);
        }

        /* Zero SMI enables in legacy control register.
         * It would prevent pre-OS code from interfering. */
        ret = async_req_3_0(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
           IPC_M_CONFIG_SPACE_WRITE_32, eecp + USBLEGCTLSTS_OFFSET, 0);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) zero USBLEGCTLSTS.\n", ret);
        usb_log_debug("Zeroed USBLEGCTLSTS register.\n");

        /* Read again Legacy Support and Control register */
        ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
            IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGCTLSTS_OFFSET, &value);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGCTLSTS.\n", ret);
        usb_log_debug2("USBLEGCTLSTS: %" PRIxn ".\n", value);

        /* Read again Legacy Support register */
        ret = async_req_2_1(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE),
            IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGSUP_OFFSET, &value);
        CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGSUP.\n", ret);
        usb_log_debug2("USBLEGSUP: %" PRIxn ".\n", value);

        /*
         * TURN OFF EHCI FOR NOW, DRIVER WILL REINITIALIZE IT
         */

        /* Get size of capability registers in memory space. */
        uint8_t operation_offset = *(uint8_t*)registers;
        usb_log_debug("USBCMD offset: %d.\n", operation_offset);

        /* Zero USBCMD register. */
        volatile uint32_t *usbcmd =
            (uint32_t*)((uint8_t*)registers + operation_offset + CMD_OFFSET);
        volatile uint32_t *usbconfigured =
            (uint32_t*)((uint8_t*)registers + operation_offset
            + CONFIGFLAG_OFFSET);
        usb_log_debug("USBCMD value: %x.\n", *usbcmd);
        if (*usbcmd & USBCMD_RUN) {
                *usbcmd = 0;
                *usbconfigured = 0;
                usb_log_info("EHCI turned off.\n");
        } else {
                usb_log_info("EHCI was not running.\n");
        }

        async_hangup(parent_phone);
        return ret;
#undef CHECK_RET_HANGUP_RETURN
}
/*----------------------------------------------------------------------------*/
/**
 * @}
 */

/**
 * @}
 */