Index: contrib/conf/dot.bochrc =================================================================== --- contrib/conf/dot.bochrc (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/conf/dot.bochrc (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,717 @@ +# You may now use double quotes around pathnames, in case +# your pathname includes spaces. + +#======================================================================= +# CONFIG_INTERFACE +# +# The configuration interface is a series of menus or dialog boxes that +# allows you to change all the settings that control Bochs's behavior. +# There are two choices of configuration interface: a text mode version +# called "textconfig" and a graphical version called "wx". The text +# mode version uses stdin/stdout and is always compiled in. The graphical +# version is only available when you use "--with-wx" on the configure +# command. If you do not write a config_interface line, Bochs will +# choose a default for you. +# +# NOTE: if you use the "wx" configuration interface, you must also use +# the "wx" display library. +#======================================================================= +config_interface: textconfig +#config_interface: wx + +#======================================================================= +# DISPLAY_LIBRARY +# +# The display library is the code that displays the Bochs VGA screen. Bochs +# has a selection of about 10 different display library implementations for +# different platforms. If you run configure with multiple --with-* options, +# the display_library command lets you choose which one you want to run with. +# If you do not write a display_library line, Bochs will choose a default for +# you. +# +# The choices are: +# x use X windows interface, cross platform +# win32 use native win32 libraries +# carbon use Carbon library (for MacOS X) +# beos use native BeOS libraries +# macintosh use MacOS pre-10 +# amigaos use native AmigaOS libraries +# sdl use SDL library, cross platform +# svga use SVGALIB library for Linux, allows graphics without X11 +# term text only, uses curses/ncurses library, cross platform +# rfb provides an interface to AT&T's VNC viewer, cross platform +# wx use wxWindows library, cross platform +# nogui no display at all +# +# NOTE: if you use the "wx" configuration interface, you must also use +# the "wx" display library. +#======================================================================= +#display_library: amigaos +#display_library: beos +#display_library: carbon +#display_library: macintosh +#display_library: nogui +#display_library: rfb +#display_library: sdl +#display_library: term +#display_library: win32 +#display_library: wx +display_library: x + +#======================================================================= +# ROMIMAGE: +# You now need to load a ROM BIOS into F0000-FFFFF. Normally, you can +# use a precompiled BIOS in the bios/ directory of the source tree, +# named BIOS-bochs-latest. +# You can also use the environment variable $BXSHARE to specify the +# location of the BIOS. +#======================================================================= +#romimage: file=$BXSHARE/BIOS-bochs-latest, address=0xf0000 +#romimage: file=bios/BIOS-bochs-2-processors, address=0xf0000 +romimage: file=$BXSHARE/BIOS-bochs-8-processors, address=0xf0000 +#romimage: file=bios/rombios.bin, address=0xf0000 + +#======================================================================= +# MEGS +# set this to the default number of Megabytes of memory you want +# to emulate. You may also pass the '-megs xyz' option to bochs +# +# The default is 32MB, most OS's won't need more than that. +#======================================================================= +#megs: 256 +#megs: 128 +#megs: 64 +megs: 32 +#megs: 16 +#megs: 8 + +#======================================================================= +# OPTROMIMAGE[1-4]: +# You may now load up to 4 optional ROM images. Be sure to use a +# read-only area, typically between C8000 and EFFFF. These optional +# ROM images should not overwrite the rombios (located at +# F0000-FFFFF) and the videobios (located at C0000-C7FFF). +# Those ROM images will be initialized by the bios if they contain +# the right signature (0x55AA). +# It can also be a convenient way to upload some arbitary code/data +# in the simulation, that can be retrieved by the boot loader +#======================================================================= +#optromimage1: file=optionalrom.bin, address=0xd0000 +#optromimage2: file=optionalrom.bin, address=0xd1000 +#optromimage3: file=optionalrom.bin, address=0xd2000 +#optromimage4: file=optionalrom.bin, address=0xd3000 + +#======================================================================= +# VGAROMIMAGE +# You now need to load a VGA ROM BIOS into C0000. +#======================================================================= +vgaromimage: $BXSHARE/VGABIOS-lgpl-latest +#vgaromimage: bios/VGABIOS-elpin-2.40 +#vgaromimage: $BXSHARE/VGABIOS-elpin-2.40 + +#======================================================================= +# FLOPPYA: +# Point this to pathname of floppy image file or device +# This should be of a bootable floppy(image/device) if you're +# booting from 'a'. +# +# You can set the initial status of the media to 'ejected' or 'inserted'. +# floppya: 2_88=path, status=ejected (2.88M 3.5" floppy) +# floppya: 1_44=path, status=inserted (1.44M 3.5" floppy) +# floppya: 1_2=path, status=ejected (1.2M 5.25" floppy) +# floppya: 720k=path, status=inserted (720K 3.5" floppy) +# floppya: 360k=path, status=inserted (360K 5.25" floppy) +# floppya: 320k=path, status=inserted (320K 5.25" floppy) +# floppya: 180k=path, status=inserted (180K 5.25" floppy) +# floppya: 160k=path, status=inserted (160K 5.25" floppy) +# +# The path should be the name of a disk image file. On unix, you can use +# a raw device name such as /dev/fd0 on Linux. On WinNT and Win2k, use +# drive letters such as a: or b: as the path. Raw floppy access is not +# supported on Windows 95 and 98. +#======================================================================= +floppya: 1_44=SPARTAN/src/image.bin, status=inserted +#floppya: 1_44=/dev/fd0, status=inserted + +#======================================================================= +# FLOPPYB: +# See FLOPPYA above for syntax +#======================================================================= +#floppyb: 1_44=b:, status=inserted +#floppyb: 1_44=b.img, status=inserted + +#======================================================================= +# ATA0, ATA1, ATA2, ATA3 +# ATA controller for hard disks and cdroms +# +# ata[0-3]: enabled=[0|1], ioaddr1=addr, ioaddr2=addr, irq=number +# +# These options enables up to 4 ata channels. For each channel +# the two base io addresses and the irq must be specified. +# +# ata0 is enabled by default, with ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 +# +# Examples: +# ata0: enabled=1, ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 +# ata1: enabled=1, ioaddr1=0x170, ioaddr2=0x370, irq=15 +# ata2: enabled=1, ioaddr1=0x1e8, ioaddr2=0x3e0, irq=11 +# ata3: enabled=1, ioaddr1=0x168, ioaddr2=0x360, irq=9 +#======================================================================= +ata0: enabled=1, ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 +ata1: enabled=0, ioaddr1=0x170, ioaddr2=0x370, irq=15 +ata2: enabled=0, ioaddr1=0x1e8, ioaddr2=0x3e0, irq=11 +ata3: enabled=0, ioaddr1=0x168, ioaddr2=0x360, irq=9 + +#======================================================================= +# ATA[0-3]-MASTER, ATA[0-3]-SLAVE +# +# This defines the type and characteristics of all attached ata devices: +# type= type of attached device [disk|cdrom] +# mode= only valid for disks [flat|concat|external|dll|sparse|vmware3] +# mode= only valid for disks [undoable|growing|volatile] +# path= path of the image +# cylinders= only valid for disks +# heads= only valid for disks +# spt= only valid for disks +# status= only valid for cdroms [inserted|ejected] +# biosdetect= type of biosdetection [none|auto], only for disks on ata0 [cmos] +# translation=type of transation of the bios, only for disks [none|lba|large|rechs|auto] +# model= string returned by identify device command +# journal= optional filename of the redolog for undoable and volatile disks +# +# Point this at a hard disk image file, cdrom iso file, or physical cdrom +# device. To create a hard disk image, try running bximage. It will help you +# choose the size and then suggest a line that works with it. +# +# In UNIX it may be possible to use a raw device as a Bochs hard disk, +# but WE DON'T RECOMMEND IT. In Windows there is no easy way. +# +# In windows, the drive letter + colon notation should be used for cdroms. +# Depending on versions of windows and drivers, you may only be able to +# access the "first" cdrom in the system. On MacOSX, use path="drive" +# to access the physical drive. +# +# The path, cylinders, heads, and spt are mandatory for type=disk +# The path is mandatory for type=cdrom +# +# Default values are: +# mode=flat, biosdetect=auto, translation=auto, model="Generic 1234" +# +# The biosdetect option has currently no effect on the bios +# +# Examples: +# ata0-master: type=disk, mode=flat, path=10M.sample, cylinders=306, heads=4, spt=17 +# ata0-slave: type=disk, mode=flat, path=20M.sample, cylinders=615, heads=4, spt=17 +# ata1-master: type=disk, mode=flat, path=30M.sample, cylinders=615, heads=6, spt=17 +# ata1-slave: type=disk, mode=flat, path=46M.sample, cylinders=940, heads=6, spt=17 +# ata2-master: type=disk, mode=flat, path=62M.sample, cylinders=940, heads=8, spt=17 +# ata2-slave: type=disk, mode=flat, path=112M.sample, cylinders=900, heads=15, spt=17 +# ata3-master: type=disk, mode=flat, path=483M.sample, cylinders=1024, heads=15, spt=63 +# ata3-slave: type=cdrom, path=iso.sample, status=inserted +#======================================================================= +#ata0-master: type=disk, mode=flat, path="30M.sample", cylinders=615, heads=6, spt=17 +#ata0-slave: type=cdrom, path=D:, status=inserted +#ata0-slave: type=cdrom, path=/dev/cdrom, status=inserted +#ata0-slave: type=cdrom, path="drive", status=inserted +#ata0-slave: type=cdrom, path=/dev/rcd0d, status=inserted + +#======================================================================= +# BOOT: +# This defines your boot drive. +# You can either boot from 'floppy', 'disk' or 'cdrom' +# legacy 'a' and 'c' are also supported +# Examples: +# boot: floppy +# boot: disk +# boot: cdrom +# boot: c +# boot: a +#======================================================================= +boot: floppy +#boot: disk + +#======================================================================= +# IPS: +# Emulated Instructions Per Second. This is the number of IPS that bochs +# is capable of running on your machine. Read the note in config.h +# on how to find this. Make sure to recompile after. +# +# IPS is used to calibrate many time-dependent events within the bochs +# simulation. For example, changing IPS affects the frequency of VGA +# updates, the duration of time before a key starts to autorepeat, and +# the measurement of BogoMips and other benchmarks. +# +# Examples: +# Machine Mips +# ________________________________________________________________ +# 650Mhz Athlon K-7 with Linux 2.4.4/egcs-2.91.66 2 to 2.5 Mips +# 400Mhz Pentium II with Linux 2.0.36/egcs-1.0.3 1 to 1.8 Mips +# 166Mhz 64bit Sparc with Solaris 2.x approx 0.75 Mips +# 200Mhz Pentium with Linux 2.x approx 0.5 Mips +# +#======================================================================= +ips: 2500000 + +#======================================================================= +# CLOCK: +# This defines the parameters of the clock inside Bochs: +# +# SYNC: +# TO BE COMPLETED (see Greg explaination in bug #536329) +# +# TIME0: +# Specifies the start (boot) time of the virtual machine. Use a time +# value as returned by the time(2) system call. If no time0 value is +# set or if time0 equal to 1 (special case) or if time0 equal 'local', +# the simulation will be started at the current local host time. +# If time0 equal to 2 (special case) or if time0 equal 'utc', +# the simulation will be started at the current utc time. +# +# Syntax: +# clock: sync=[none|slowdown|realtime], time0=[timeValue|local|utc] +# +# Example: +# clock: sync=none, time0=local # Now (localtime) +# clock: sync=slowdown, time0=315529200 # Tue Jan 1 00:00:00 1980 +# clock: sync=none, time0=631148400 # Mon Jan 1 00:00:00 1990 +# clock: sync=realtime, time0=938581955 # Wed Sep 29 07:12:35 1999 +# clock: sync=realtime, time0=946681200 # Sat Jan 1 00:00:00 2000 +# clock: sync=none, time0=1 # Now (localtime) +# clock: sync=none, time0=utc # Now (utc/gmt) +# +# Default value are sync=none, time0=local +#======================================================================= +clock: sync=none, time0=local + + +#======================================================================= +# FLOPPY_BOOTSIG_CHECK: disabled=[0|1] +# Enables or disables the 0xaa55 signature check on boot floppies +# Defaults to disabled=0 +# Examples: +# floppy_bootsig_check: disabled=0 +# floppy_bootsig_check: disabled=1 +#======================================================================= +#floppy_bootsig_check: disabled=1 +floppy_bootsig_check: disabled=1 + +#======================================================================= +# LOG: +# Give the path of the log file you'd like Bochs debug and misc. verbage +# to be written to. If you really don't want it, make it /dev/null. :^( +# +# Examples: +# log: ./bochs.out +# log: /dev/tty +#======================================================================= +#log: /dev/null +log: bochsout.txt + +#======================================================================= +# LOGPREFIX: +# This handles the format of the string prepended to each log line. +# You may use those special tokens : +# %t : 11 decimal digits timer tick +# %i : 8 hexadecimal digits of cpu0 current eip +# %e : 1 character event type ('i'nfo, 'd'ebug, 'p'anic, 'e'rror) +# %d : 5 characters string of the device, between brackets +# +# Default : %t%e%d +# Examples: +# logprefix: %t-%e-@%i-%d +# logprefix: %i%e%d +#======================================================================= +#logprefix: %t%e%d + +#======================================================================= +# LOG CONTROLS +# +# Bochs now has four severity levels for event logging. +# panic: cannot proceed. If you choose to continue after a panic, +# don't be surprised if you get strange behavior or crashes. +# error: something went wrong, but it is probably safe to continue the +# simulation. +# info: interesting or useful messages. +# debug: messages useful only when debugging the code. This may +# spit out thousands per second. +# +# For events of each level, you can choose to crash, report, or ignore. +# TODO: allow choice based on the facility: e.g. crash on panics from +# everything except the cdrom, and only report those. +# +# If you are experiencing many panics, it can be helpful to change +# the panic action to report instead of fatal. However, be aware +# that anything executed after a panic is uncharted territory and can +# cause bochs to become unstable. The panic is a "graceful exit," so +# if you disable it you may get a spectacular disaster instead. +#======================================================================= +panic: action=ask +error: action=report +info: action=report +debug: action=ignore +#pass: action=fatal + +#======================================================================= +# DEBUGGER_LOG: +# Give the path of the log file you'd like Bochs to log debugger output. +# If you really don't want it, make it /dev/null or '-'. :^( +# +# Examples: +# debugger_log: ./debugger.out +#======================================================================= +#debugger_log: /dev/null +#debugger_log: debugger.out +debugger_log: - + +#======================================================================= +# COM1: +# This defines a serial port (UART type 16550A). You can specify a device +# to use as com1. This can be a real serial line, or a pty. To use a pty +# (under X/Unix), create two windows (xterms, usually). One of them will +# run bochs, and the other will act as com1. Find out the tty the com1 +# window using the `tty' command, and use that as the `dev' parameter. +# Then do `sleep 1000000' in the com1 window to keep the shell from +# messing with things, and run bochs in the other window. Serial I/O to +# com1 (port 0x3f8) will all go to the other window. +#======================================================================= +#com1: enabled=1, dev=/dev/ttyp9 + + +#======================================================================= +# PARPORT1: +# This defines a parallel (printer) port. When turned on and an output file is +# defined the emulated printer port sends characters printed by the guest OS +# into the output file. On some platforms a device filename can be used to +# send the data to the real parallel port (e.g. "/dev/lp0" on Linux, "lpt1" on +# win32 platforms). +# +# Examples: +# parport1: enabled=1, file="parport.out" +# parport1: enabled=1, file="/dev/lp0" +# parport1: enabled=0 +#======================================================================= +parport1: enabled=1, file="parport.out" + +#======================================================================= +# SB16: +# This defines the SB16 sound emulation. It can have several of the +# following properties. +# All properties are in the format sb16: property=value +# midi: The filename is where the midi data is sent. This can be a +# device or just a file if you want to record the midi data. +# midimode: +# 0=no data +# 1=output to device (system dependent. midi denotes the device driver) +# 2=SMF file output, including headers +# 3=output the midi data stream to the file (no midi headers and no +# delta times, just command and data bytes) +# wave: This is the device/file where wave output is stored +# wavemode: +# 0=no data +# 1=output to device (system dependent. wave denotes the device driver) +# 2=VOC file output, incl. headers +# 3=output the raw wave stream to the file +# log: The file to write the sb16 emulator messages to. +# loglevel: +# 0=no log +# 1=only midi program and bank changes +# 2=severe errors +# 3=all errors +# 4=all errors plus all port accesses +# 5=all errors and port accesses plus a lot of extra info +# dmatimer: +# microseconds per second for a DMA cycle. Make it smaller to fix +# non-continous sound. 750000 is usually a good value. This needs a +# reasonably correct setting for IPS. +# +# For an example look at the next line: +#======================================================================= + +#sb16: midimode=1, midi=/dev/midi00, wavemode=1, wave=/dev/dsp, loglevel=2, log=sb16.log, dmatimer=600000 + +#======================================================================= +# VGA_UPDATE_INTERVAL: +# Video memory is scanned for updates and screen updated every so many +# virtual seconds. The default is 300000, about 3Hz. This is generally +# plenty. Keep in mind that you must tweak the 'ips:' directive +# to be as close to the number of emulated instructions-per-second +# your workstation can do, for this to be accurate. +# +# Examples: +# vga_update_interval: 250000 +#======================================================================= +vga_update_interval: 300000 + +# using for Winstone '98 tests +#vga_update_interval: 100000 + +#======================================================================= +# KEYBOARD_SERIAL_DELAY: +# Approximate time in microseconds that it takes one character to +# be transfered from the keyboard to controller over the serial path. +# Examples: +# keyboard_serial_delay: 200 +#======================================================================= +keyboard_serial_delay: 250 + +#======================================================================= +# KEYBOARD_PASTE_DELAY: +# Approximate time in microseconds between attempts to paste +# characters to the keyboard controller. This leaves time for the +# guest os to deal with the flow of characters. The ideal setting +# depends on how your operating system processes characters. The +# default of 100000 usec (.1 seconds) was chosen because it works +# consistently in Windows. +# +# If your OS is losing characters during a paste, increase the paste +# delay until it stops losing characters. +# +# Examples: +# keyboard_paste_delay: 100000 +#======================================================================= +keyboard_paste_delay: 100000 + +#======================================================================= +# FLOPPY_COMMAND_DELAY: +# Time in microseconds to wait before completing some floppy commands +# such as read/write/seek/etc, which normally have a delay associated. +# I had this hardwired to 50,000 before. +# +# Examples: +# floppy_command_delay: 50000 +#======================================================================= +floppy_command_delay: 500 + +#======================================================================= +# MOUSE: +# This option prevents Bochs from creating mouse "events" unless a mouse +# is enabled. The hardware emulation itself is not disabled by this. +# You can turn the mouse on by setting enabled to 1, or turn it off by +# setting enabled to 0. Unless you have a particular reason for enabling +# the mouse by default, it is recommended that you leave it off. +# You can also toggle the mouse usage at runtime (middle mouse button on +# X11 and SDL, F12 on Win32). +# +# Examples: +# mouse: enabled=1 +# mouse: enabled=0 +#======================================================================= +mouse: enabled=0 + +#======================================================================= +# private_colormap: Request that the GUI create and use it's own +# non-shared colormap. This colormap will be used +# when in the bochs window. If not enabled, a +# shared colormap scheme may be used. Not implemented +# on all GUI's. +# +# Examples: +# private_colormap: enabled=1 +# private_colormap: enabled=0 +#======================================================================= +private_colormap: enabled=0 + +#======================================================================= +# fullscreen: ONLY IMPLEMENTED ON AMIGA +# Request that Bochs occupy the entire screen instead of a +# window. +# +# Examples: +# fullscreen: enabled=0 +# fullscreen: enabled=1 +#======================================================================= +#fullscreen: enabled=0 +#screenmode: name="sample" + +#======================================================================= +# ne2k: NE2000 compatible ethernet adapter +# +# Examples: +# ne2k: ioaddr=IOADDR, irq=IRQ, mac=MACADDR, ethmod=MODULE, ethdev=DEVICE, script=SCRIPT +# +# ioaddr, irq: You probably won't need to change ioaddr and irq, unless there +# are IRQ conflicts. +# +# mac: The MAC address MUST NOT match the address of any machine on the net. +# Also, the first byte must be an even number (bit 0 set means a multicast +# address), and you cannot use ff:ff:ff:ff:ff:ff because that's the broadcast +# address. For the ethertap module, you must use fe:fd:00:00:00:01. There may +# be other restrictions too. To be safe, just use the b0:c4... address. +# +# ethdev: The ethdev value is the name of the network interface on your host +# platform. On UNIX machines, you can get the name by running ifconfig. On +# Windows machines, you must run niclist to get the name of the ethdev. +# Niclist source code is in misc/niclist.c and it is included in Windows +# binary releases. +# +# script: The script value is optionnal, and is the name of a script that +# is executed after bochs initialize the network interface. You can use +# this script to configure this network interface, or enable masquerading. +# This is mainly useful for the tun/tap devices that only exist during +# Bochs execution. The network interface name is supplied to the script +# as first parameter +#======================================================================= +# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=fbsd, ethdev=en0 #macosx +# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:00, ethmod=fbsd, ethdev=xl0 +# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:00, ethmod=linux, ethdev=eth0 +# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:01, ethmod=win32, ethdev=MYCARD +# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=tap, ethdev=tap0 +# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=tuntap, ethdev=tun0, script=./tunconfig + +#======================================================================= +# KEYBOARD_MAPPING: +# This enables a remap of a physical localized keyboard to a +# virtualized us keyboard, as the PC architecture expects. +# If enabled, the keymap file must be specified. +# +# Examples: +# keyboard_mapping: enabled=1, map=gui/keymaps/x11-pc-de.map +#======================================================================= +keyboard_mapping: enabled=0, map= + +#======================================================================= +# KEYBOARD_TYPE: +# Type of keyboard return by a "identify keyboard" command to the +# keyboard controler. It must be one of "xt", "at" or "mf". +# Defaults to "mf". It should be ok for almost everybody. A known +# exception is french macs, that do have a "at"-like keyboard. +# +# Examples: +# keyboard_type: mf +#======================================================================= +#keyboard_type: mf + +#======================================================================= +# USER_SHORTCUT: +# This defines the keyboard shortcut to be sent when you press the "user" +# button in the headerbar. The shortcut string can be a combination of +# these key names: "alt", "bksp", "ctrl", "del", "esc", "f1", "f4", "tab" +# and "win". Up to 3 keys can be pressed at a time. +# +# Example: +# user_shortcut: keys=ctrlaltdel +#======================================================================= +#user_shortcut: keys=ctrlaltdel + +#======================================================================= +# other stuff +#======================================================================= +#magic_break: enabled=1 +#cmosimage: cmos.img +#load32bitOSImage: os=nullkernel, path=../kernel.img, iolog=../vga_io.log +#load32bitOSImage: os=linux, path=../linux.img, iolog=../vga_io.log, initrd=../initrd.img +#i440fxsupport: enabled=1 +usb1: enabled=1, ioaddr=0xFF80, irq=10 +#text_snapshot_check: enable + +#======================================================================= +# for Macintosh, use the style of pathnames in the following +# examples. +# +# vgaromimage: :bios:VGABIOS-elpin-2.40 +# romimage: file=:bios:BIOS-bochs-latest, address=0xf0000 +# floppya: 1_44=[fd:], status=inserted +#======================================================================= + + +#======================================================================= +# +# The following directives are DEPRECATED +# Please convert them to the new syntax or remove them +# +#======================================================================= + +#======================================================================= +# +# The DISKC option is deprecated. Use ATA* options instead. +# +# DISKC: file=, cyl=, heads=, spt= +# Point this at a hard disk image file. To create +# a hard disk image, try running bximage. It will help you choose the +# size and then suggest a diskc line that works with it. +# +# In UNIX it may be possible to use a raw device as a Bochs hard disk, +# but WE DON'T RECOMMEND IT. In Windows there is no easy way. +# +# Examples: +# diskc: file=10M.sample, cyl=306, heads=4, spt=17 +# diskc: file=20M.sample, cyl=615, heads=4, spt=17 +# diskc: file=30M.sample, cyl=615, heads=6, spt=17 +# diskc: file=46M.sample, cyl=940, heads=6, spt=17 +# diskc: file=62M.sample, cyl=940, heads=8, spt=17 +# diskc: file=112M.sample, cyl=900, heads=15, spt=17 +# diskc: file=483M.sample, cyl=1024, heads=15, spt=63 +#======================================================================= +#diskc: file="30M.sample", cyl=615, heads=6, spt=17 + +#======================================================================= +# +# The DISKD option is deprecated. Use ATA* options instead. +# +# DISKD: +# See DISKC above for syntax +# +# NOTE: diskd and cdromd must not be used together! +#======================================================================= +#diskd: file="diskd.img", cyl=615, heads=6, spt=17 + +#======================================================================= +# +# The CDROMD option is deprecated. Use ATA* options instead. +# +# CDROMD: +# +# cdromd: dev=/dev/cdrom, status=inserted +# cdromd: dev=/dev/cdrom, status=ejected +# cdromd: dev=e:, status=ejected +# +# In windows, the drive letter + colon notation should be used for cdroms. +# Depending on versions of windows and drivers, you may only be able to +# access the "first" cdrom in the system. On MacOSX, use path="drive" +# to access the physical drive. +# +# NOTE: diskd and cdromd must not be used together! +#======================================================================= +#cdromd: dev=D:, status=inserted +#cdromd: dev=/dev/cdrom, status=inserted +#cdromd: dev="drive", status=inserted + +#======================================================================= +# +# The TIME0 directive is DEPRECATED. Use the CLOCK directive instead +# +# TIME0: +# Specifies the start (boot) time of the virtual machine. Use a time +# value as returned by the time(2) system call. If no time0 value is +# set or if time0 equal to 1 (special case), the simulation will be +# started at the current time of the host. +# +# Examples: +# time0: 1 # Now +# time0: 315529200 # Tue Jan 1 00:00:00 1980 +# time0: 631148400 # Mon Jan 1 00:00:00 1990 +# time0: 938581955 # Wed Sep 29 07:12:35 1999 +# time0: 946681200 # Sat Jan 1 00:00:00 2000 +#======================================================================= +#time0: 938581955 + +#======================================================================= +# +# The PIT directive is DEPRECATED. Use the CLOCK directive instead +# +# PIT: +# The PIT is the programmable interval timer. It has an option that tries to +# keep the PIT in sync with real time. This feature is still experimental, +# but it may be useful if you want to prevent Bochs from running too fast, for +# example a DOS video game. Be aware that with the realtime pit option, your +# simulation will not be repeatable; this can a problem if you are debugging. +#======================================================================= +#pit: realtime=1 + +#======================================================================= +# NEWHARDDRIVESUPPORT: enabled=[0|1] +# The old harddrive code is not maintened any more. +# Default value is enabled=1 +#======================================================================= +#newharddrivesupport: enabled=1 + Index: contrib/conf/msim.conf =================================================================== --- contrib/conf/msim.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/conf/msim.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,10 @@ +# +# MSIM configuration script +# + +add dcpu mips1 + +add rwm mainmem 0 16M load "kernel.bin" +add rom startmem 0x1fc00000 1k load "load.bin" + +add dprinter printer 0x10000000 Index: contrib/conf/pearpc.conf =================================================================== --- contrib/conf/pearpc.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/conf/pearpc.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,5 @@ +ppc_start_resolution = "800x600x32" +pci_ide0_master_installed = 0 + +prom_bootmethod = "force" +prom_loadfile = "kernel.bin" Index: contrib/conf/ski.conf =================================================================== --- contrib/conf/ski.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/conf/ski.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,2 @@ +load SPARTAN/src/kernel.bin +load SPARTAN/src/load.bin Index: contrib/conf/vmware.conf =================================================================== --- contrib/conf/vmware.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/conf/vmware.conf (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,15 @@ +#!/opt/vmware/bin/vmware +config.version = "8" +virtualHW.version = "4" +scsi0.present = "FALSE" +memsize = "96" +ide0:0.present = "FALSE" +ide1:0.present = "FALSE" +floppy0.startConnected = "TRUE" +floppy0.fileType = "file" +floppy0.fileName = "image.bin" +sound.present = "FALSE" +displayName = "HelenOS" +guestOS = "other" +nvram = "HelenOS.nvram" +isolation.tools.hgfs.disable = "TRUE" Index: contrib/dot.bochrc =================================================================== --- contrib/dot.bochrc (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,717 +1,0 @@ -# You may now use double quotes around pathnames, in case -# your pathname includes spaces. - -#======================================================================= -# CONFIG_INTERFACE -# -# The configuration interface is a series of menus or dialog boxes that -# allows you to change all the settings that control Bochs's behavior. -# There are two choices of configuration interface: a text mode version -# called "textconfig" and a graphical version called "wx". The text -# mode version uses stdin/stdout and is always compiled in. The graphical -# version is only available when you use "--with-wx" on the configure -# command. If you do not write a config_interface line, Bochs will -# choose a default for you. -# -# NOTE: if you use the "wx" configuration interface, you must also use -# the "wx" display library. -#======================================================================= -config_interface: textconfig -#config_interface: wx - -#======================================================================= -# DISPLAY_LIBRARY -# -# The display library is the code that displays the Bochs VGA screen. Bochs -# has a selection of about 10 different display library implementations for -# different platforms. If you run configure with multiple --with-* options, -# the display_library command lets you choose which one you want to run with. -# If you do not write a display_library line, Bochs will choose a default for -# you. -# -# The choices are: -# x use X windows interface, cross platform -# win32 use native win32 libraries -# carbon use Carbon library (for MacOS X) -# beos use native BeOS libraries -# macintosh use MacOS pre-10 -# amigaos use native AmigaOS libraries -# sdl use SDL library, cross platform -# svga use SVGALIB library for Linux, allows graphics without X11 -# term text only, uses curses/ncurses library, cross platform -# rfb provides an interface to AT&T's VNC viewer, cross platform -# wx use wxWindows library, cross platform -# nogui no display at all -# -# NOTE: if you use the "wx" configuration interface, you must also use -# the "wx" display library. -#======================================================================= -#display_library: amigaos -#display_library: beos -#display_library: carbon -#display_library: macintosh -#display_library: nogui -#display_library: rfb -#display_library: sdl -#display_library: term -#display_library: win32 -#display_library: wx -display_library: x - -#======================================================================= -# ROMIMAGE: -# You now need to load a ROM BIOS into F0000-FFFFF. Normally, you can -# use a precompiled BIOS in the bios/ directory of the source tree, -# named BIOS-bochs-latest. -# You can also use the environment variable $BXSHARE to specify the -# location of the BIOS. -#======================================================================= -#romimage: file=$BXSHARE/BIOS-bochs-latest, address=0xf0000 -#romimage: file=bios/BIOS-bochs-2-processors, address=0xf0000 -romimage: file=$BXSHARE/BIOS-bochs-8-processors, address=0xf0000 -#romimage: file=bios/rombios.bin, address=0xf0000 - -#======================================================================= -# MEGS -# set this to the default number of Megabytes of memory you want -# to emulate. You may also pass the '-megs xyz' option to bochs -# -# The default is 32MB, most OS's won't need more than that. -#======================================================================= -#megs: 256 -#megs: 128 -#megs: 64 -megs: 32 -#megs: 16 -#megs: 8 - -#======================================================================= -# OPTROMIMAGE[1-4]: -# You may now load up to 4 optional ROM images. Be sure to use a -# read-only area, typically between C8000 and EFFFF. These optional -# ROM images should not overwrite the rombios (located at -# F0000-FFFFF) and the videobios (located at C0000-C7FFF). -# Those ROM images will be initialized by the bios if they contain -# the right signature (0x55AA). -# It can also be a convenient way to upload some arbitary code/data -# in the simulation, that can be retrieved by the boot loader -#======================================================================= -#optromimage1: file=optionalrom.bin, address=0xd0000 -#optromimage2: file=optionalrom.bin, address=0xd1000 -#optromimage3: file=optionalrom.bin, address=0xd2000 -#optromimage4: file=optionalrom.bin, address=0xd3000 - -#======================================================================= -# VGAROMIMAGE -# You now need to load a VGA ROM BIOS into C0000. -#======================================================================= -vgaromimage: $BXSHARE/VGABIOS-lgpl-latest -#vgaromimage: bios/VGABIOS-elpin-2.40 -#vgaromimage: $BXSHARE/VGABIOS-elpin-2.40 - -#======================================================================= -# FLOPPYA: -# Point this to pathname of floppy image file or device -# This should be of a bootable floppy(image/device) if you're -# booting from 'a'. -# -# You can set the initial status of the media to 'ejected' or 'inserted'. -# floppya: 2_88=path, status=ejected (2.88M 3.5" floppy) -# floppya: 1_44=path, status=inserted (1.44M 3.5" floppy) -# floppya: 1_2=path, status=ejected (1.2M 5.25" floppy) -# floppya: 720k=path, status=inserted (720K 3.5" floppy) -# floppya: 360k=path, status=inserted (360K 5.25" floppy) -# floppya: 320k=path, status=inserted (320K 5.25" floppy) -# floppya: 180k=path, status=inserted (180K 5.25" floppy) -# floppya: 160k=path, status=inserted (160K 5.25" floppy) -# -# The path should be the name of a disk image file. On unix, you can use -# a raw device name such as /dev/fd0 on Linux. On WinNT and Win2k, use -# drive letters such as a: or b: as the path. Raw floppy access is not -# supported on Windows 95 and 98. -#======================================================================= -floppya: 1_44=SPARTAN/src/image.bin, status=inserted -#floppya: 1_44=/dev/fd0, status=inserted - -#======================================================================= -# FLOPPYB: -# See FLOPPYA above for syntax -#======================================================================= -#floppyb: 1_44=b:, status=inserted -#floppyb: 1_44=b.img, status=inserted - -#======================================================================= -# ATA0, ATA1, ATA2, ATA3 -# ATA controller for hard disks and cdroms -# -# ata[0-3]: enabled=[0|1], ioaddr1=addr, ioaddr2=addr, irq=number -# -# These options enables up to 4 ata channels. For each channel -# the two base io addresses and the irq must be specified. -# -# ata0 is enabled by default, with ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 -# -# Examples: -# ata0: enabled=1, ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 -# ata1: enabled=1, ioaddr1=0x170, ioaddr2=0x370, irq=15 -# ata2: enabled=1, ioaddr1=0x1e8, ioaddr2=0x3e0, irq=11 -# ata3: enabled=1, ioaddr1=0x168, ioaddr2=0x360, irq=9 -#======================================================================= -ata0: enabled=1, ioaddr1=0x1f0, ioaddr2=0x3f0, irq=14 -ata1: enabled=0, ioaddr1=0x170, ioaddr2=0x370, irq=15 -ata2: enabled=0, ioaddr1=0x1e8, ioaddr2=0x3e0, irq=11 -ata3: enabled=0, ioaddr1=0x168, ioaddr2=0x360, irq=9 - -#======================================================================= -# ATA[0-3]-MASTER, ATA[0-3]-SLAVE -# -# This defines the type and characteristics of all attached ata devices: -# type= type of attached device [disk|cdrom] -# mode= only valid for disks [flat|concat|external|dll|sparse|vmware3] -# mode= only valid for disks [undoable|growing|volatile] -# path= path of the image -# cylinders= only valid for disks -# heads= only valid for disks -# spt= only valid for disks -# status= only valid for cdroms [inserted|ejected] -# biosdetect= type of biosdetection [none|auto], only for disks on ata0 [cmos] -# translation=type of transation of the bios, only for disks [none|lba|large|rechs|auto] -# model= string returned by identify device command -# journal= optional filename of the redolog for undoable and volatile disks -# -# Point this at a hard disk image file, cdrom iso file, or physical cdrom -# device. To create a hard disk image, try running bximage. It will help you -# choose the size and then suggest a line that works with it. -# -# In UNIX it may be possible to use a raw device as a Bochs hard disk, -# but WE DON'T RECOMMEND IT. In Windows there is no easy way. -# -# In windows, the drive letter + colon notation should be used for cdroms. -# Depending on versions of windows and drivers, you may only be able to -# access the "first" cdrom in the system. On MacOSX, use path="drive" -# to access the physical drive. -# -# The path, cylinders, heads, and spt are mandatory for type=disk -# The path is mandatory for type=cdrom -# -# Default values are: -# mode=flat, biosdetect=auto, translation=auto, model="Generic 1234" -# -# The biosdetect option has currently no effect on the bios -# -# Examples: -# ata0-master: type=disk, mode=flat, path=10M.sample, cylinders=306, heads=4, spt=17 -# ata0-slave: type=disk, mode=flat, path=20M.sample, cylinders=615, heads=4, spt=17 -# ata1-master: type=disk, mode=flat, path=30M.sample, cylinders=615, heads=6, spt=17 -# ata1-slave: type=disk, mode=flat, path=46M.sample, cylinders=940, heads=6, spt=17 -# ata2-master: type=disk, mode=flat, path=62M.sample, cylinders=940, heads=8, spt=17 -# ata2-slave: type=disk, mode=flat, path=112M.sample, cylinders=900, heads=15, spt=17 -# ata3-master: type=disk, mode=flat, path=483M.sample, cylinders=1024, heads=15, spt=63 -# ata3-slave: type=cdrom, path=iso.sample, status=inserted -#======================================================================= -#ata0-master: type=disk, mode=flat, path="30M.sample", cylinders=615, heads=6, spt=17 -#ata0-slave: type=cdrom, path=D:, status=inserted -#ata0-slave: type=cdrom, path=/dev/cdrom, status=inserted -#ata0-slave: type=cdrom, path="drive", status=inserted -#ata0-slave: type=cdrom, path=/dev/rcd0d, status=inserted - -#======================================================================= -# BOOT: -# This defines your boot drive. -# You can either boot from 'floppy', 'disk' or 'cdrom' -# legacy 'a' and 'c' are also supported -# Examples: -# boot: floppy -# boot: disk -# boot: cdrom -# boot: c -# boot: a -#======================================================================= -boot: floppy -#boot: disk - -#======================================================================= -# IPS: -# Emulated Instructions Per Second. This is the number of IPS that bochs -# is capable of running on your machine. Read the note in config.h -# on how to find this. Make sure to recompile after. -# -# IPS is used to calibrate many time-dependent events within the bochs -# simulation. For example, changing IPS affects the frequency of VGA -# updates, the duration of time before a key starts to autorepeat, and -# the measurement of BogoMips and other benchmarks. -# -# Examples: -# Machine Mips -# ________________________________________________________________ -# 650Mhz Athlon K-7 with Linux 2.4.4/egcs-2.91.66 2 to 2.5 Mips -# 400Mhz Pentium II with Linux 2.0.36/egcs-1.0.3 1 to 1.8 Mips -# 166Mhz 64bit Sparc with Solaris 2.x approx 0.75 Mips -# 200Mhz Pentium with Linux 2.x approx 0.5 Mips -# -#======================================================================= -ips: 2500000 - -#======================================================================= -# CLOCK: -# This defines the parameters of the clock inside Bochs: -# -# SYNC: -# TO BE COMPLETED (see Greg explaination in bug #536329) -# -# TIME0: -# Specifies the start (boot) time of the virtual machine. Use a time -# value as returned by the time(2) system call. If no time0 value is -# set or if time0 equal to 1 (special case) or if time0 equal 'local', -# the simulation will be started at the current local host time. -# If time0 equal to 2 (special case) or if time0 equal 'utc', -# the simulation will be started at the current utc time. -# -# Syntax: -# clock: sync=[none|slowdown|realtime], time0=[timeValue|local|utc] -# -# Example: -# clock: sync=none, time0=local # Now (localtime) -# clock: sync=slowdown, time0=315529200 # Tue Jan 1 00:00:00 1980 -# clock: sync=none, time0=631148400 # Mon Jan 1 00:00:00 1990 -# clock: sync=realtime, time0=938581955 # Wed Sep 29 07:12:35 1999 -# clock: sync=realtime, time0=946681200 # Sat Jan 1 00:00:00 2000 -# clock: sync=none, time0=1 # Now (localtime) -# clock: sync=none, time0=utc # Now (utc/gmt) -# -# Default value are sync=none, time0=local -#======================================================================= -clock: sync=none, time0=local - - -#======================================================================= -# FLOPPY_BOOTSIG_CHECK: disabled=[0|1] -# Enables or disables the 0xaa55 signature check on boot floppies -# Defaults to disabled=0 -# Examples: -# floppy_bootsig_check: disabled=0 -# floppy_bootsig_check: disabled=1 -#======================================================================= -#floppy_bootsig_check: disabled=1 -floppy_bootsig_check: disabled=1 - -#======================================================================= -# LOG: -# Give the path of the log file you'd like Bochs debug and misc. verbage -# to be written to. If you really don't want it, make it /dev/null. :^( -# -# Examples: -# log: ./bochs.out -# log: /dev/tty -#======================================================================= -#log: /dev/null -log: bochsout.txt - -#======================================================================= -# LOGPREFIX: -# This handles the format of the string prepended to each log line. -# You may use those special tokens : -# %t : 11 decimal digits timer tick -# %i : 8 hexadecimal digits of cpu0 current eip -# %e : 1 character event type ('i'nfo, 'd'ebug, 'p'anic, 'e'rror) -# %d : 5 characters string of the device, between brackets -# -# Default : %t%e%d -# Examples: -# logprefix: %t-%e-@%i-%d -# logprefix: %i%e%d -#======================================================================= -#logprefix: %t%e%d - -#======================================================================= -# LOG CONTROLS -# -# Bochs now has four severity levels for event logging. -# panic: cannot proceed. If you choose to continue after a panic, -# don't be surprised if you get strange behavior or crashes. -# error: something went wrong, but it is probably safe to continue the -# simulation. -# info: interesting or useful messages. -# debug: messages useful only when debugging the code. This may -# spit out thousands per second. -# -# For events of each level, you can choose to crash, report, or ignore. -# TODO: allow choice based on the facility: e.g. crash on panics from -# everything except the cdrom, and only report those. -# -# If you are experiencing many panics, it can be helpful to change -# the panic action to report instead of fatal. However, be aware -# that anything executed after a panic is uncharted territory and can -# cause bochs to become unstable. The panic is a "graceful exit," so -# if you disable it you may get a spectacular disaster instead. -#======================================================================= -panic: action=ask -error: action=report -info: action=report -debug: action=ignore -#pass: action=fatal - -#======================================================================= -# DEBUGGER_LOG: -# Give the path of the log file you'd like Bochs to log debugger output. -# If you really don't want it, make it /dev/null or '-'. :^( -# -# Examples: -# debugger_log: ./debugger.out -#======================================================================= -#debugger_log: /dev/null -#debugger_log: debugger.out -debugger_log: - - -#======================================================================= -# COM1: -# This defines a serial port (UART type 16550A). You can specify a device -# to use as com1. This can be a real serial line, or a pty. To use a pty -# (under X/Unix), create two windows (xterms, usually). One of them will -# run bochs, and the other will act as com1. Find out the tty the com1 -# window using the `tty' command, and use that as the `dev' parameter. -# Then do `sleep 1000000' in the com1 window to keep the shell from -# messing with things, and run bochs in the other window. Serial I/O to -# com1 (port 0x3f8) will all go to the other window. -#======================================================================= -#com1: enabled=1, dev=/dev/ttyp9 - - -#======================================================================= -# PARPORT1: -# This defines a parallel (printer) port. When turned on and an output file is -# defined the emulated printer port sends characters printed by the guest OS -# into the output file. On some platforms a device filename can be used to -# send the data to the real parallel port (e.g. "/dev/lp0" on Linux, "lpt1" on -# win32 platforms). -# -# Examples: -# parport1: enabled=1, file="parport.out" -# parport1: enabled=1, file="/dev/lp0" -# parport1: enabled=0 -#======================================================================= -parport1: enabled=1, file="parport.out" - -#======================================================================= -# SB16: -# This defines the SB16 sound emulation. It can have several of the -# following properties. -# All properties are in the format sb16: property=value -# midi: The filename is where the midi data is sent. This can be a -# device or just a file if you want to record the midi data. -# midimode: -# 0=no data -# 1=output to device (system dependent. midi denotes the device driver) -# 2=SMF file output, including headers -# 3=output the midi data stream to the file (no midi headers and no -# delta times, just command and data bytes) -# wave: This is the device/file where wave output is stored -# wavemode: -# 0=no data -# 1=output to device (system dependent. wave denotes the device driver) -# 2=VOC file output, incl. headers -# 3=output the raw wave stream to the file -# log: The file to write the sb16 emulator messages to. -# loglevel: -# 0=no log -# 1=only midi program and bank changes -# 2=severe errors -# 3=all errors -# 4=all errors plus all port accesses -# 5=all errors and port accesses plus a lot of extra info -# dmatimer: -# microseconds per second for a DMA cycle. Make it smaller to fix -# non-continous sound. 750000 is usually a good value. This needs a -# reasonably correct setting for IPS. -# -# For an example look at the next line: -#======================================================================= - -#sb16: midimode=1, midi=/dev/midi00, wavemode=1, wave=/dev/dsp, loglevel=2, log=sb16.log, dmatimer=600000 - -#======================================================================= -# VGA_UPDATE_INTERVAL: -# Video memory is scanned for updates and screen updated every so many -# virtual seconds. The default is 300000, about 3Hz. This is generally -# plenty. Keep in mind that you must tweak the 'ips:' directive -# to be as close to the number of emulated instructions-per-second -# your workstation can do, for this to be accurate. -# -# Examples: -# vga_update_interval: 250000 -#======================================================================= -vga_update_interval: 300000 - -# using for Winstone '98 tests -#vga_update_interval: 100000 - -#======================================================================= -# KEYBOARD_SERIAL_DELAY: -# Approximate time in microseconds that it takes one character to -# be transfered from the keyboard to controller over the serial path. -# Examples: -# keyboard_serial_delay: 200 -#======================================================================= -keyboard_serial_delay: 250 - -#======================================================================= -# KEYBOARD_PASTE_DELAY: -# Approximate time in microseconds between attempts to paste -# characters to the keyboard controller. This leaves time for the -# guest os to deal with the flow of characters. The ideal setting -# depends on how your operating system processes characters. The -# default of 100000 usec (.1 seconds) was chosen because it works -# consistently in Windows. -# -# If your OS is losing characters during a paste, increase the paste -# delay until it stops losing characters. -# -# Examples: -# keyboard_paste_delay: 100000 -#======================================================================= -keyboard_paste_delay: 100000 - -#======================================================================= -# FLOPPY_COMMAND_DELAY: -# Time in microseconds to wait before completing some floppy commands -# such as read/write/seek/etc, which normally have a delay associated. -# I had this hardwired to 50,000 before. -# -# Examples: -# floppy_command_delay: 50000 -#======================================================================= -floppy_command_delay: 500 - -#======================================================================= -# MOUSE: -# This option prevents Bochs from creating mouse "events" unless a mouse -# is enabled. The hardware emulation itself is not disabled by this. -# You can turn the mouse on by setting enabled to 1, or turn it off by -# setting enabled to 0. Unless you have a particular reason for enabling -# the mouse by default, it is recommended that you leave it off. -# You can also toggle the mouse usage at runtime (middle mouse button on -# X11 and SDL, F12 on Win32). -# -# Examples: -# mouse: enabled=1 -# mouse: enabled=0 -#======================================================================= -mouse: enabled=0 - -#======================================================================= -# private_colormap: Request that the GUI create and use it's own -# non-shared colormap. This colormap will be used -# when in the bochs window. If not enabled, a -# shared colormap scheme may be used. Not implemented -# on all GUI's. -# -# Examples: -# private_colormap: enabled=1 -# private_colormap: enabled=0 -#======================================================================= -private_colormap: enabled=0 - -#======================================================================= -# fullscreen: ONLY IMPLEMENTED ON AMIGA -# Request that Bochs occupy the entire screen instead of a -# window. -# -# Examples: -# fullscreen: enabled=0 -# fullscreen: enabled=1 -#======================================================================= -#fullscreen: enabled=0 -#screenmode: name="sample" - -#======================================================================= -# ne2k: NE2000 compatible ethernet adapter -# -# Examples: -# ne2k: ioaddr=IOADDR, irq=IRQ, mac=MACADDR, ethmod=MODULE, ethdev=DEVICE, script=SCRIPT -# -# ioaddr, irq: You probably won't need to change ioaddr and irq, unless there -# are IRQ conflicts. -# -# mac: The MAC address MUST NOT match the address of any machine on the net. -# Also, the first byte must be an even number (bit 0 set means a multicast -# address), and you cannot use ff:ff:ff:ff:ff:ff because that's the broadcast -# address. For the ethertap module, you must use fe:fd:00:00:00:01. There may -# be other restrictions too. To be safe, just use the b0:c4... address. -# -# ethdev: The ethdev value is the name of the network interface on your host -# platform. On UNIX machines, you can get the name by running ifconfig. On -# Windows machines, you must run niclist to get the name of the ethdev. -# Niclist source code is in misc/niclist.c and it is included in Windows -# binary releases. -# -# script: The script value is optionnal, and is the name of a script that -# is executed after bochs initialize the network interface. You can use -# this script to configure this network interface, or enable masquerading. -# This is mainly useful for the tun/tap devices that only exist during -# Bochs execution. The network interface name is supplied to the script -# as first parameter -#======================================================================= -# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=fbsd, ethdev=en0 #macosx -# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:00, ethmod=fbsd, ethdev=xl0 -# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:00, ethmod=linux, ethdev=eth0 -# ne2k: ioaddr=0x240, irq=9, mac=b0:c4:20:00:00:01, ethmod=win32, ethdev=MYCARD -# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=tap, ethdev=tap0 -# ne2k: ioaddr=0x240, irq=9, mac=fe:fd:00:00:00:01, ethmod=tuntap, ethdev=tun0, script=./tunconfig - -#======================================================================= -# KEYBOARD_MAPPING: -# This enables a remap of a physical localized keyboard to a -# virtualized us keyboard, as the PC architecture expects. -# If enabled, the keymap file must be specified. -# -# Examples: -# keyboard_mapping: enabled=1, map=gui/keymaps/x11-pc-de.map -#======================================================================= -keyboard_mapping: enabled=0, map= - -#======================================================================= -# KEYBOARD_TYPE: -# Type of keyboard return by a "identify keyboard" command to the -# keyboard controler. It must be one of "xt", "at" or "mf". -# Defaults to "mf". It should be ok for almost everybody. A known -# exception is french macs, that do have a "at"-like keyboard. -# -# Examples: -# keyboard_type: mf -#======================================================================= -#keyboard_type: mf - -#======================================================================= -# USER_SHORTCUT: -# This defines the keyboard shortcut to be sent when you press the "user" -# button in the headerbar. The shortcut string can be a combination of -# these key names: "alt", "bksp", "ctrl", "del", "esc", "f1", "f4", "tab" -# and "win". Up to 3 keys can be pressed at a time. -# -# Example: -# user_shortcut: keys=ctrlaltdel -#======================================================================= -#user_shortcut: keys=ctrlaltdel - -#======================================================================= -# other stuff -#======================================================================= -#magic_break: enabled=1 -#cmosimage: cmos.img -#load32bitOSImage: os=nullkernel, path=../kernel.img, iolog=../vga_io.log -#load32bitOSImage: os=linux, path=../linux.img, iolog=../vga_io.log, initrd=../initrd.img -#i440fxsupport: enabled=1 -usb1: enabled=1, ioaddr=0xFF80, irq=10 -#text_snapshot_check: enable - -#======================================================================= -# for Macintosh, use the style of pathnames in the following -# examples. -# -# vgaromimage: :bios:VGABIOS-elpin-2.40 -# romimage: file=:bios:BIOS-bochs-latest, address=0xf0000 -# floppya: 1_44=[fd:], status=inserted -#======================================================================= - - -#======================================================================= -# -# The following directives are DEPRECATED -# Please convert them to the new syntax or remove them -# -#======================================================================= - -#======================================================================= -# -# The DISKC option is deprecated. Use ATA* options instead. -# -# DISKC: file=, cyl=, heads=, spt= -# Point this at a hard disk image file. To create -# a hard disk image, try running bximage. It will help you choose the -# size and then suggest a diskc line that works with it. -# -# In UNIX it may be possible to use a raw device as a Bochs hard disk, -# but WE DON'T RECOMMEND IT. In Windows there is no easy way. -# -# Examples: -# diskc: file=10M.sample, cyl=306, heads=4, spt=17 -# diskc: file=20M.sample, cyl=615, heads=4, spt=17 -# diskc: file=30M.sample, cyl=615, heads=6, spt=17 -# diskc: file=46M.sample, cyl=940, heads=6, spt=17 -# diskc: file=62M.sample, cyl=940, heads=8, spt=17 -# diskc: file=112M.sample, cyl=900, heads=15, spt=17 -# diskc: file=483M.sample, cyl=1024, heads=15, spt=63 -#======================================================================= -#diskc: file="30M.sample", cyl=615, heads=6, spt=17 - -#======================================================================= -# -# The DISKD option is deprecated. Use ATA* options instead. -# -# DISKD: -# See DISKC above for syntax -# -# NOTE: diskd and cdromd must not be used together! -#======================================================================= -#diskd: file="diskd.img", cyl=615, heads=6, spt=17 - -#======================================================================= -# -# The CDROMD option is deprecated. Use ATA* options instead. -# -# CDROMD: -# -# cdromd: dev=/dev/cdrom, status=inserted -# cdromd: dev=/dev/cdrom, status=ejected -# cdromd: dev=e:, status=ejected -# -# In windows, the drive letter + colon notation should be used for cdroms. -# Depending on versions of windows and drivers, you may only be able to -# access the "first" cdrom in the system. On MacOSX, use path="drive" -# to access the physical drive. -# -# NOTE: diskd and cdromd must not be used together! -#======================================================================= -#cdromd: dev=D:, status=inserted -#cdromd: dev=/dev/cdrom, status=inserted -#cdromd: dev="drive", status=inserted - -#======================================================================= -# -# The TIME0 directive is DEPRECATED. Use the CLOCK directive instead -# -# TIME0: -# Specifies the start (boot) time of the virtual machine. Use a time -# value as returned by the time(2) system call. If no time0 value is -# set or if time0 equal to 1 (special case), the simulation will be -# started at the current time of the host. -# -# Examples: -# time0: 1 # Now -# time0: 315529200 # Tue Jan 1 00:00:00 1980 -# time0: 631148400 # Mon Jan 1 00:00:00 1990 -# time0: 938581955 # Wed Sep 29 07:12:35 1999 -# time0: 946681200 # Sat Jan 1 00:00:00 2000 -#======================================================================= -#time0: 938581955 - -#======================================================================= -# -# The PIT directive is DEPRECATED. Use the CLOCK directive instead -# -# PIT: -# The PIT is the programmable interval timer. It has an option that tries to -# keep the PIT in sync with real time. This feature is still experimental, -# but it may be useful if you want to prevent Bochs from running too fast, for -# example a DOS video game. Be aware that with the realtime pit option, your -# simulation will not be repeatable; this can a problem if you are debugging. -#======================================================================= -#pit: realtime=1 - -#======================================================================= -# NEWHARDDRIVESUPPORT: enabled=[0|1] -# The old harddrive code is not maintened any more. -# Default value is enabled=1 -#======================================================================= -#newharddrivesupport: enabled=1 - Index: contrib/msim.conf =================================================================== --- contrib/msim.conf (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,10 +1,0 @@ -# -# MSIM configuration script -# - -add dcpu mips1 - -add rwm mainmem 0 16M load "kernel.bin" -add rom startmem 0x1fc00000 1k load "load.bin" - -add dprinter printer 0x10000000 Index: contrib/pearpc.conf =================================================================== --- contrib/pearpc.conf (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,5 +1,0 @@ -ppc_start_resolution = "800x600x32" -pci_ide0_master_installed = 0 - -prom_bootmethod = "force" -prom_loadfile = "kernel.bin" Index: contrib/ski.conf =================================================================== --- contrib/ski.conf (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,2 +1,0 @@ -load SPARTAN/src/kernel.bin -load SPARTAN/src/load.bin Index: contrib/toolchain.amd64.sh =================================================================== --- contrib/toolchain.amd64.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,84 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="amd64" -WORKDIR=`pwd` -TARGET="${PLATFORM}-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain.ia32.sh =================================================================== --- contrib/toolchain.ia32.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,84 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="i686" -WORKDIR=`pwd` -TARGET="${PLATFORM}-pc-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain.ia64.sh =================================================================== --- contrib/toolchain.ia64.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,93 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -INCLUDES="ia64-pc-gnu-linux_includes.tar.bz2" -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -INCLUDES_SOURCE="http://download.decky.cz/" -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="ia64" -WORKDIR=`pwd` -TARGET="${PLATFORM}-pc-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -INCLUDESDIR="${WORKDIR}/include" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${INCLUDES}" ]; then - wget -c "${INCLUDES_SOURCE}${INCLUDES}" - check_error $? "Error downloading includes." -fi -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvjf "${INCLUDES}" -check_error $? "Error unpacking includes." -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj "--with-headers=${INCLUDESDIR}" --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain.mips.sh =================================================================== --- contrib/toolchain.mips.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,84 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="mipsel" -WORKDIR=`pwd` -TARGET="${PLATFORM}-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain.ppc.sh =================================================================== --- contrib/toolchain.ppc.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,84 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="ppc" -WORKDIR=`pwd` -TARGET="${PLATFORM}-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain.ppc64.sh =================================================================== --- contrib/toolchain.ppc64.sh (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,84 +1,0 @@ -#!/bin/bash - -# Cross-Compiler Toolchain for ${PLATFORM} -# by Martin Decky -# -# GPL'ed, copyleft -# - - -check_error() { - if [ "$1" -ne "0" ]; then - echo - echo "Script failed: $2" - exit - fi -} - -BINUTILS_VERSION="2.16" -GCC_VERSION="4.0.1" - -BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" -GCC="gcc-core-${GCC_VERSION}.tar.bz2" - -BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" -GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" - -PLATFORM="ppc64" -WORKDIR=`pwd` -TARGET="${PLATFORM}-linux-gnu" -HOST="i686-pc-linux-gnu" -PREFIX="/usr/local/${PLATFORM}" -BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" -GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" -OBJDIR="${WORKDIR}/gcc-obj" - -echo ">>> Downloading tarballs" - -if [ ! -f "${BINUTILS}" ]; then - wget -c "${BINUTILS_SOURCE}${BINUTILS}" - check_error $? "Error downloading binutils." -fi -if [ ! -f "${GCC}" ]; then - wget -c "${GCC_SOURCE}${GCC}" - check_error $? "Error downloading GCC." -fi - -echo ">>> Creating destionation directory" -if [ ! -d "${PREFIX}" ]; then - mkdir -p "${PREFIX}" - test -d "${PREFIX}" - check_error $? "Unable to create ${PREFIX}." -fi - -echo ">>> Creating GCC work directory" -if [ ! -d "${OBJDIR}" ]; then - mkdir -p "${OBJDIR}" - test -d "${OBJDIR}" - check_error $? "Unable to create ${OBJDIR}." -fi - -echo ">>> Unpacking tarballs" -tar -xvzf "${BINUTILS}" -check_error $? "Error unpacking binutils." -tar -xvjf "${GCC}" -check_error $? "Error unpacking GCC." - -echo ">>> Compiling and installing binutils" -cd "${BINUTILSDIR}" -check_error $? "Change directory failed." -./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" -check_error $? "Error configuring binutils." -make all install -check_error $? "Error compiling/installing binutils." - -echo ">>> Compiling and installing GCC" -cd "${OBJDIR}" -check_error $? "Change directory failed." -"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared -check_error $? "Error configuring GCC." -PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc -check_error $? "Error compiling/installing GCC." - -echo -echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.amd64.sh =================================================================== --- contrib/toolchain/toolchain.amd64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.amd64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,84 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="amd64" +WORKDIR=`pwd` +TARGET="${PLATFORM}-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.ia32.sh =================================================================== --- contrib/toolchain/toolchain.ia32.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.ia32.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,84 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="i686" +WORKDIR=`pwd` +TARGET="${PLATFORM}-pc-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.ia64.sh =================================================================== --- contrib/toolchain/toolchain.ia64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.ia64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,93 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +INCLUDES="ia64-pc-gnu-linux_includes.tar.bz2" +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +INCLUDES_SOURCE="http://download.decky.cz/" +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="ia64" +WORKDIR=`pwd` +TARGET="${PLATFORM}-pc-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +INCLUDESDIR="${WORKDIR}/include" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${INCLUDES}" ]; then + wget -c "${INCLUDES_SOURCE}${INCLUDES}" + check_error $? "Error downloading includes." +fi +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvjf "${INCLUDES}" +check_error $? "Error unpacking includes." +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj "--with-headers=${INCLUDESDIR}" --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.mips.sh =================================================================== --- contrib/toolchain/toolchain.mips.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.mips.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,84 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="mipsel" +WORKDIR=`pwd` +TARGET="${PLATFORM}-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.ppc.sh =================================================================== --- contrib/toolchain/toolchain.ppc.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.ppc.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,84 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="ppc" +WORKDIR=`pwd` +TARGET="${PLATFORM}-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/toolchain/toolchain.ppc64.sh =================================================================== --- contrib/toolchain/toolchain.ppc64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) +++ contrib/toolchain/toolchain.ppc64.sh (revision be56c17fb7a40db7401fc109228679d3c7c5cb40) @@ -0,0 +1,84 @@ +#!/bin/bash + +# Cross-Compiler Toolchain for ${PLATFORM} +# by Martin Decky +# +# GPL'ed, copyleft +# + + +check_error() { + if [ "$1" -ne "0" ]; then + echo + echo "Script failed: $2" + exit + fi +} + +BINUTILS_VERSION="2.16" +GCC_VERSION="4.0.1" + +BINUTILS="binutils-${BINUTILS_VERSION}.tar.gz" +GCC="gcc-core-${GCC_VERSION}.tar.bz2" + +BINUTILS_SOURCE="ftp://ftp.gnu.org/gnu/binutils/" +GCC_SOURCE="ftp://ftp.gnu.org/gnu/gcc/gcc-${GCC_VERSION}/" + +PLATFORM="ppc64" +WORKDIR=`pwd` +TARGET="${PLATFORM}-linux-gnu" +HOST="i686-pc-linux-gnu" +PREFIX="/usr/local/${PLATFORM}" +BINUTILSDIR="${WORKDIR}/binutils-${BINUTILS_VERSION}" +GCCDIR="${WORKDIR}/gcc-${GCC_VERSION}" +OBJDIR="${WORKDIR}/gcc-obj" + +echo ">>> Downloading tarballs" + +if [ ! -f "${BINUTILS}" ]; then + wget -c "${BINUTILS_SOURCE}${BINUTILS}" + check_error $? "Error downloading binutils." +fi +if [ ! -f "${GCC}" ]; then + wget -c "${GCC_SOURCE}${GCC}" + check_error $? "Error downloading GCC." +fi + +echo ">>> Creating destionation directory" +if [ ! -d "${PREFIX}" ]; then + mkdir -p "${PREFIX}" + test -d "${PREFIX}" + check_error $? "Unable to create ${PREFIX}." +fi + +echo ">>> Creating GCC work directory" +if [ ! -d "${OBJDIR}" ]; then + mkdir -p "${OBJDIR}" + test -d "${OBJDIR}" + check_error $? "Unable to create ${OBJDIR}." +fi + +echo ">>> Unpacking tarballs" +tar -xvzf "${BINUTILS}" +check_error $? "Error unpacking binutils." +tar -xvjf "${GCC}" +check_error $? "Error unpacking GCC." + +echo ">>> Compiling and installing binutils" +cd "${BINUTILSDIR}" +check_error $? "Change directory failed." +./configure "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--disable-nls" +check_error $? "Error configuring binutils." +make all install +check_error $? "Error compiling/installing binutils." + +echo ">>> Compiling and installing GCC" +cd "${OBJDIR}" +check_error $? "Change directory failed." +"${GCCDIR}/configure" "--host=${HOST}" "--target=${TARGET}" "--prefix=${PREFIX}" "--program-prefix=${TARGET}-" --with-gnu-as --with-gnu-ld --disable-nls --disable-threads --enable-languages=c --disable-multilib --disable-libgcj --without-headers --disable-shared +check_error $? "Error configuring GCC." +PATH="${PATH}:${PREFIX}/bin" make all-gcc install-gcc +check_error $? "Error compiling/installing GCC." + +echo +echo ">>> Cross-compiler for ${TARGET} installed." Index: contrib/vmware.conf =================================================================== --- contrib/vmware.conf (revision 27934427258b587f8a178b2f21465dc1cd3f6660) +++ (revision ) @@ -1,15 +1,0 @@ -#!/opt/vmware/bin/vmware -config.version = "8" -virtualHW.version = "4" -scsi0.present = "FALSE" -memsize = "96" -ide0:0.present = "FALSE" -ide1:0.present = "FALSE" -floppy0.startConnected = "TRUE" -floppy0.fileType = "file" -floppy0.fileName = "image.bin" -sound.present = "FALSE" -displayName = "HelenOS" -guestOS = "other" -nvram = "HelenOS.nvram" -isolation.tools.hgfs.disable = "TRUE"