Changes in uspace/drv/ehci-hcd/pci.c [67352d2:4125b7d] in mainline
- File:
-
- 1 edited
Legend:
- Unmodified
- Added
- Removed
-
uspace/drv/ehci-hcd/pci.c
r67352d2 r4125b7d 117 117 mem_address = res->res.mem_range.address; 118 118 mem_size = res->res.mem_range.size; 119 usb_log_debug2("Found mem: % llx%zu.\n",119 usb_log_debug2("Found mem: %" PRIxn" %zu.\n", 120 120 mem_address, mem_size); 121 121 mem_found = true; … … 186 186 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read PCI config space.\n", 187 187 ret); 188 usb_log_info("Register space BAR at %p:% x.\n",address, value);188 usb_log_info("Register space BAR at %p:%" PRIxn ".\n", (void *) address, value); 189 189 190 190 /* clear lower byte, it's not part of the BASE address */ 191 191 uintptr_t registers = (value & 0xffffff00); 192 usb_log_info("Memory registers BASE address:%p.\n", registers);192 usb_log_info("Memory registers BASE address:%p.\n", (void *) registers); 193 193 194 194 /* if nothing setup the hc, we don't need to turn it off */ … … 201 201 AS_AREA_READ | AS_AREA_WRITE); 202 202 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to map registers %p:%p.\n", 203 ret, regs, registers);203 ret, regs, (void *) registers); 204 204 205 205 /* calculate value of BASE */ … … 221 221 IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGCTLSTS_OFFSET, &value); 222 222 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGCTLSTS.\n", ret); 223 usb_log_debug("USBLEGCTLSTS: % x.\n", value);223 usb_log_debug("USBLEGCTLSTS: %" PRIxn ".\n", value); 224 224 225 225 /* Read the first EEC. i.e. Legacy Support register */ … … 228 228 IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGSUP_OFFSET, &value); 229 229 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGSUP.\n", ret); 230 usb_log_debug2("USBLEGSUP: % x.\n", value);230 usb_log_debug2("USBLEGSUP: %" PRIxn ".\n", value); 231 231 232 232 /* Request control from firmware/BIOS, by writing 1 to highest byte. … … 248 248 249 249 if ((value & USBLEGSUP_BIOS_CONTROL) == 0) { 250 usb_log_info("BIOS released control after % dusec.\n", wait);250 usb_log_info("BIOS released control after %zu usec.\n", wait); 251 251 } else { 252 252 /* BIOS failed to hand over control, this should not happen. */ 253 253 usb_log_warning( "BIOS failed to release control after " 254 "% dusecs, force it.\n", wait);254 "%zu usecs, force it.\n", wait); 255 255 ret = async_req_3_0(parent_phone, DEV_IFACE_ID(PCI_DEV_IFACE), 256 256 IPC_M_CONFIG_SPACE_WRITE_32, eecp + USBLEGSUP_OFFSET, … … 271 271 IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGCTLSTS_OFFSET, &value); 272 272 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGCTLSTS.\n", ret); 273 usb_log_debug2("USBLEGCTLSTS: % x.\n", value);273 usb_log_debug2("USBLEGCTLSTS: %" PRIxn ".\n", value); 274 274 275 275 /* Read again Legacy Support register */ … … 277 277 IPC_M_CONFIG_SPACE_READ_32, eecp + USBLEGSUP_OFFSET, &value); 278 278 CHECK_RET_HANGUP_RETURN(ret, "Failed(%d) to read USBLEGSUP.\n", ret); 279 usb_log_debug2("USBLEGSUP: % x.\n", value);279 usb_log_debug2("USBLEGSUP: %" PRIxn ".\n", value); 280 280 281 281 /*
Note:
See TracChangeset
for help on using the changeset viewer.